ph16 3112g 10/100base smd transformer module feature designed to meet ieee802.3u r equirement. turn ratio 1:1 on transmitter side ? g ? stand for rohs. primary inductance 350 m h min. with 8ma dc b ias designed to meet ir 2 60 0 c peak requirement. specifications @ 25 0 c parameter condition min. typ. max. unit inductance @100khz,100mv, pin(16 - 14) & pin(11 - 9) 350 * note 1 m h turn ratio pin(1 - 3) : (16 - 14) 1 : 1 5% pin(6 - 8) : (11 - 9) 1 : 1 5% leakage inductance 0.5 m h interwinding capacitance 28 pf dcr pin(1 - 3)& pin(6 - 8) 0.7 w pin(16 - 14)& pin(11 - 9) 1.1 w insertion l oss @1 - 100mhz - 1.0 db return l oss @1 - 30mhz - 16 db @30 - 60mhz *note 2 db @60 - 80mhz - 10 db cross t alk @1 - 60mhz - 40 db @ 60 - 100mhz - 38 db cmrr @1 - 60mhz - 45/ - 40 db @60 - 100mhz - 40/ - 35 db voltage isolation 1500 vrms note 1: measured at 8madc over operating temperature 0~70 0 c note 2 : greater than 16 - 20 lo g(f/30 mhz)db dimension schematic unless otherwise specified , all tolerances are mm(inch) 0.25(0.01) tape & reel applications r dps - ph 283 (r 1 ) 07/11 /200 5 data s heet s ubject to c hange w ithout n otice sheet 1 of 2 t x+ t x - ct r x+ r x - ct 1 3 16 1 5 1 4 6 7 8 1 1 9 td+ ct td - r d+ ct rd - 10 2 weight . . . . . . . . . 0.8 grams typ tape & reel . . . . . 750/reel tube . . . . . . . . . . . 37/tube
PH163112G test requirements and procedures no item requirement test or inspection method 1 examination of product meet requirements of product drawing v is ual , x - ray , microscope and so on. 2 solderability max. 5% de - wetting, inspection with 10 times magnification. after steamy 1 hrs , dip solder 260 0 c duration: 2 0.5 seconds. ref: sony technical standards ss - 00254 - 1 &ss - 00254 - 2 3 res istance to soldering heat no functional damage. smt: peak temp. 260 0 c ref: sony technical standards ss - 00254 - 4 &ss - 00254 - 5 4 vibration no physical damage. random vibration / overall : 1.15 g rms freq. (hz) : 1 4 100 200 psd (g 2 / hz) : 0.0001 0.01 0.01 0.001 test axis/ time : top / 30 mins bottom / 10 mins x axis : 10 mins y axis : 10 mins ref :ista project 2a 5 thermal shock contact resistance, insulation resistance shall meet each specified requirement . mold ed product : ?e 40 0 c ?? 125 0 c for 5 cycles (25 , 50 , 100 cycles for d.v.t. ) ref:mil - std - 202 method 107 6 temperature - humidity exposure contact resistance, insulation resistance shall meet each specified requirement . molded product : - 1 0 0 c~65 0 c / 95% r.h / bias 100 vdc 96 hrs(168 , 500 hrs for d.v.t) ref:mil - std - 202 method 103 7 high temperature exposure contact resistance insulation resistance shall meet each specified requirement molded product : ?? 125 0 c ?a bias: 25 vdc 96 hrs(168 , 500 hrs for d.v.t ) ref: mil - std - 202 method 103 rdps - ph283(r1)07/11/2005 data sheet subject to change without notice sheet 2 of 2
|
